manualshive.com logo in svg

Taylor C723, Руководство по обслуживанию, Страница: 7 / 88

Поделиться
Скачать
Taylor C723 Скачать руководство пользователя страница 7

 3

Model C723

Introduction

 THIS UNIT HAS MANY SHARP EDGES

THAT CAN CAUSE SEVERE INJURIES.

Examples:

S

scraper blades

S

condenser fins

S

cup/cone dispenser (if applicable)

 This unit must be installed on a level

surface to avoid the hazard of tipping. Extreme care
should be taken in moving this equipment for any
reason. Two or more people are required to safely
move this unit. Failure to comply may result in
personal injury or equipment damage.

This unit must 

NOT

 be installed in an area

where a water jet or hose can be used. 

NEVER 

use

a water jet or hose to rinse or clean this unit. Using a
water jet or hose on or around this equipment may
result in the electrocution of the user or damage to
the equipment.

 Cleaning and sanitizing schedules are

governed by your state or local regulatory agencies
and must be followed accordingly. Please refer to
the cleaning section of the Operator Manual for the
proper procedure to clean this unit.

Authorized service personnel must ensure

that the proper PPE (Personal Protective
Equipment) is available and worn when required
during installation and service.

Содержание C723

























































































Отзывы:

Нет отзывов