Taylor-Dunn SC-100-24 Скачать руководство пользователя

Страница: 90 / 126

Hardware

Page 90

SC-100

MA-100-03

TORQUE GUIDELINES FOR STANDARD HARDWARE

Note: Torque values specified are for clean dry threads.

Note: Torque value used shall be for lowest grade of hardware used. If a grade 2 nut is used on a grade 8 bolt,

use grade 2 torque value.

Hardware Identification

Hex Head Bolts and Screws

The grade of SAE bolts and screws are identified by markings on the head

as illustrated to the right.
The grade of a metric hex head bolt or screw is cast directly on the head.

Below is an example of a 10.9. The location and style of the text will vary.

SAE Grade 2

SAE Grade 5

SAE Grade 8

SAE Grade 9

Other types of bolts and screws

Truss Head, Grade 2

Carriage Bolt, Grade 2

Содержание SC-100-24































































































































Результаты поиска

Содержание SC-100-24

Отзывы:

Похожие инструкции для SC-100-24

Бренды по названию

Популярные бренды

Taylor-Dunn SC-100-24, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание SC-100-24

Отзывы:

Похожие инструкции для SC-100-24

Бренды по названию

Популярные бренды