Taylor-Dunn SC-100-24 Скачать руководство пользователя

Страница: 34 / 126

Transaxle-GT

Page 34

SC-100

MA-100-03

REAR HUB, ROTOR & BEARINGS

Note: The axle hub bolt has a special thread

locking compound applied to the threads. If

this bolt is removed, it must be replaced.

1: Disconnect the batteries.

2: Raise the wheel off of the ground.

3: Release the park brake.

4: Remove the tire/wheel assembly, Refer to Tires

and Wheels section for information regarding

removing the tire/wheel assembly.

5: Remove the axle hub bolt and washer and

remove the hub from the axle.

6: Remove the outer brake pad. Refer to section

Brake Service for information regarding removing

the brake pads.

7: Remove the rotor.

8: If also replacing the bearing, the axle shaft must

be removed from the housing. Refer to Axle

Shaft procedure for information on removing and

installing the axle shaft.

9: Install in reverse order.

a. Thoroughly clean the threads in the axle shaft.

b. Lightly grease the hub splines.

c. Refer to Brakes section for information regarding

installing the brake pads.

d. Using a new bolt, torque the axle hub bolt to the

specification listed in the table at the end of this

section.

e. Refer to Tires and Wheels section for information

regarding installing the tire/wheel assembly.

10: Set the park brake.

11: Lower the wheel to the ground.

12: Reconnect the batteries.

13: Remove the blocks from behind the wheels,

release the park brake and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

The axle retaining plate bolts have a pre-applied

thread locking compound. They are intended for one

time use only. If removed they must be replaced.

Reusing the original bolts could cause loss of brakes

resulting in severe bodily injury and/or property

damage.

WARNING

MOTOR REMOVAL

Note: Some applications will require removing the

drive assembly from the vehicle to remove

the motor. Refer to Removing and Installing

the Drive Assembly for information on

removing the drive assembly.

1: Disconnect the batteries

2: Remove the wires from the motor.

Note: Label the motor wires with the number of

the motor terminal before they are removed

from the motor.

3: Remove the motor support bracket U-bolt (only

used on larger motors).

4: Remove the motor mounting bolts and slide the

motor off of the input shaft.

5: Install the motor in reverse order. Make sure that

the motor coupler o-ring is properly installed on

the transmission input shaft. Refer to the torque

table in the motor section for tightening the motor

terminals.

6: Apply a light coating of moly paste grease

part number 94-421-34 to the splines on the

transmission input shaft only.

7: Reconnect the batteries.

8: Remove the blocks from behind the

wheels.

9: Release the park brake and test drive.

Transmission input shaft

Содержание SC-100-24































































































































Результаты поиска

Содержание SC-100-24

Отзывы:

Похожие инструкции для SC-100-24

Бренды по названию

Популярные бренды

Taylor-Dunn SC-100-24, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание SC-100-24

Отзывы:

Похожие инструкции для SC-100-24

Бренды по названию

Популярные бренды