Taylor-Dunn SC-100-24 Скачать руководство пользователя

Страница: 35 / 126

Transaxle-GT

Page 35

MA-100-03

SC-100

PRIMARY GEAR CASE

1: Disconnect the batteries.

2: Raise the rear of the vehicle and support with

jack stands.

3: Place a drain pan under the gear case that is

capable of holding 4 liters (4 quarts) of oil and

drain the oil from the front gear case.

4: If required, remove the drive assembly from the vehicle. Refer to

Remove assembly procedure.

5: Remove the motor only if the entire drive is to be disassembled. Refer to

Motor procedure.

6: Remove the cover retaining bolts.

7: Remove the cover plate and let the remaining oil drain from the housing.

8: Remove the circlip from the idler gear.

9: Remove the input shaft/bearing assembly and idler gear/bearing

assembly from the gear case cover at the same time.

10: Remove the pinion nut from the output gear and remove the output gear

from the pinion shaft.

Note: If necessary, remove the seal from the input shaft bore at this time.

11: Mark the gear case position in relation to the 3rd member housing so

that it will be reassembled in the same position.

12: Remove the six retaining bolts holding the gear case to the 3rd member

housing.

13: Remove the gear case housing from the 3rd member housing.

14: Inspect all parts for signs of wear or damage.

15: Assemble the gear case in reverse order.

a. Apply gasket sealer (#94-430-05) to the front flange on the 3rd member

and gear case cover.

b. Pack the motor seal with non-acetic based grease.

c . Torque the drain plug, gear case to 3rd member bolts, and pinion nut per torque listed in the Hardware

Torque table at the end of this section.

16:

Fill the differential with oil. Refer to Check Oil Level for information on filling the drive with oil.

17: Lower the vehicle.

18: Reconnect the batteries.

19: Remove the blocks from behind the wheels.

20: Test drive the vehicle.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Idler Gear Circlip

Remove Idler & Input Assy.

Содержание SC-100-24































































































































Результаты поиска

Содержание SC-100-24

Отзывы:

Похожие инструкции для SC-100-24

Бренды по названию

Популярные бренды

Taylor-Dunn SC-100-24, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание SC-100-24

Отзывы:

Похожие инструкции для SC-100-24

Бренды по названию

Популярные бренды