Taylor-Dunn SC-100-24 Скачать руководство пользователя

Страница: 44 / 126

Transaxle

Page 44

modelnumber

manualnumber

REAR HUB, ROTOR & BEARINGS

Note: The axle hub bolt has a special thread

locking compound applied to the threads. If

this bolt is removed, it must be replaced.

Note: If replacing the bearing, the axle shaft must

be removed from the housing. Refer to Axle

Shaft procedure for information on removing

and installing the axle shaft.

Note: This procedure refers to other procedures

that can be found in this section or other

sections of this manual.

1: Raise the wheel off of the ground.

2: Release the park brake.

3: Remove the tire/wheel assembly.

4: Remove the axle hub bolt and washer and

remove the hub from the axle.

5: Remove the outer brake pad.

6: Remove the rotor.

7: Install in reverse order.

•

Thoroughly clean the threads in the axle shaft.

•

Lightly grease the hub splines.

•

Refer to Brakes section for information

regarding installing the brake pads.

•

Using a new bolt, torque the axle hub bolt to

the specification listed in the table at the end of

this section.

•

Refer to Tires and Wheels section for

information regarding installing the tire/wheel

assembly.

8: Set the park brake.

9: Lower the wheel to the ground and test drive.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

The axle retaining plate bolts have a pre-applied

thread locking compound. They are intended for one

time use only. If removed they must be replaced.

Reusing the original bolts could cause loss of brakes

resulting in severe bodily injury and/or property

damage.

WARNING

MOTOR, REMOVE

Note: Some applications may require removing

the drive assembly from the vehicle to

remove the motor. Refer to Removing and

Installing the Drive Assembly for information

on removing the drive assembly.

1: Remove the wires from the motor.

2: Remove the motor support bracket U-bolt (only

used on larger motors).

3: Remove the motor mounting bolts and slide the

motor off of the input shaft.

Inspect the input shaft O-ring and replace as

needed.

5: Install the motor in reverse order.

6: Apply a light coating of moly paste grease

part number 94-421-34 to the splines on the

transmission input shaft only.

Make sure that the motor coupler O-ring is

properly installed on the transmission input shaft.

8: Refer to the torque table in the motor section for

tightening the motor terminals.

9: Reconnect the batteries and test drive.

Transmission input shaft

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

The hub bolts have a pre-applied thread locking

compound. They are intended for one time use only. If

removed they must be replaced. Reusing the original

bolts could result in a wheel separating from the axle

and loss of brakes resulting in severe bodily injury

and/or property damage.

WARNING

Содержание SC-100-24































































































































Результаты поиска

Содержание SC-100-24

Отзывы:

Похожие инструкции для SC-100-24

Бренды по названию

Популярные бренды

Taylor-Dunn SC-100-24, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание SC-100-24

Отзывы:

Похожие инструкции для SC-100-24

Бренды по названию

Популярные бренды