Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 101

Страница: 101 / 188

Motor Controller

Page 101

MB-210-13

B-200 & B-210 Models

TROUBLESHOOTING

Troubleshooting control system is not included in this

manual.
All electrical troubleshooting information is included in

a separate manual “Troubleshooting Electric Vehicles”.

part number M7-001-69.
This manual was provided on the original vehicle CD.

A hard copy can be purchased from your authorized

Taylor-Dunn distributor or can be downloaded from the

Taylor-Dunn web site.

REPAIR/PROGRAMMING

Repairs

There are no internally serviceable components in the

motor speed controllers. If a controller is faulty then it

must be replaced.

Note: Opening or disassembling a controller will

void the controller warranty.

Programming

Taylor-Dunn does not support field modifications to the

controller parameters.
Complete vehicle parameters are available by e-mail

and can be uploaded to the controller using a laptop or

PC with the PCpaK application and cable. Refer to the

Tools section for part numbers.

If you have a special application that may require modified

parameters, contact your local authorized Taylor-Dunn

distributor to submit a request to the factory. Note: There

may be a fee to created a custom parameter set.
Instructions for obtaining parameter sets and how to

upload to the controller are included with the application.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

The controller power base and logic are a matched

set. DO NOT swap logics from one base to another as

this may damage the logic or power base.

NOTICE

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды