Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 115

Страница: 115 / 188

Tires & Wheels

Page 115

MB-210-13

B-200 & B-210 Models

TREAD WEAR

It is important to periodically inspect each tires tread for

wear. Driving with inadequate tread increases the risk

of loosing control of the vehicle due to hydroplaning on

a wet road surface. It also increases the risk of a flat tire

due to road debris. Extreme tire wear can result in sudden

tire failure and loss of control of the vehicle.
Refer to the maintenance schedule in this manual for the

recommended interval.
Minimum recommended tread depth is 1/16 inch (1.6

mm). There are a series of tread depth wear indicators

around the circumference of the tire. They will appear as

approximately 1/2 inch (12 mm) bands across the tread

as the tire approaches its wear limit (see illustration).

The tire should be replaced if any tread depth indicator

can be seen or any part of the tread depth is 1/16 inch

(1.6 mm) or less.

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

DO NOT operate a vehicle if the cord is

visible on any tire (see illustration). A tire

in this conditions may suddenly fail at

any time and cause loss of control of the

vehicle.

WARNING

ROTATION

Front and rear tires as well as left and right tires can wear at different rates. It is important

to periodically rotate your ties to extend your tire life. Refer to the maintenance schedule

in this manual for the recommended interval.
Use the following pattern for a vehicle with no spare tire:

•

Right Rear to Right Front

•

Right Front to Left Rear

•

Left Rear to Left Front

•

Left Front to Right Rear

Use the following pattern for a vehicle with spare tire:

•

Right Rear to Right Front

•

Right Front to Left Rear

•

Left Rear to Spare

•

Spare to Left Front

•

Left Front to Right Rear

This section is one section of a complete service

manual. Before starting any procedure, read all

warnings and instructions that are located in the

Service Guidelines chapter.

WARNING

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды