Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 59

Страница: 59 / 188

Drive Axle

Page 59

MB-210-13

B-200 & B-210 Models

12: Using a soft metal or hard wood dowel, drive

the intermediate shaft through the bearing just

enough to allow clearance for an ID bearing

puller. Do not attempt to drive the shaft out of the

opposite end of the transmission.

13: Remove the intermediate bearing with an ID

bearing puller.

14: While supporting the shaft and gear assembly,

repeat steps #12 and #13 for the opposite side

bearing and remove the intermediate shaft from

the housing.

15: Remove the o-rings from each end of the

intermediate shaft.

16: Remove the circlip from the input shaft.

17: Remove the input shaft from the housing.

18: Press the bearings off of the input shaft.

19: Remove the o-rings from both sides of the

intermediate shaft bore and the input shaft bore

and discard the o-rings.

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды