Taylor-Dunn B0-200-00 Скачать руководство пользователя страница 86

Страница: 86 / 188

Brakes

Page 86

B-200 & B-210 Models

MB-210-13

BRAKE ADJUSTMENT

Service Brake
Mechanical and Hydraulic Brakes

The mechanical and hydraulic brake assemblies are

identical except for hydraulic fittings. The adjustment

procedure is the same for both the mechanical and

hydraulic brakes.

Note: The brake adjustment is inside of the left

and right brake. Do not adjust the brake

by means of the brake cables as this will

cause mis-operation of the brakes. If you

hear a single “clunking” noise while braking

it may be due to mis-adjustment of the

brake cables or linkage. Refer to

Replace

Brake Linkages/Cables

for information

regarding proper adjustment of the cables

and linkages.

1: Raise the wheel off of the ground and support

with jack stands.

2: Release the park brake.

3: Remove the tire/wheel assembly.

Note: Refer to

Tires and Wheels

section for

information on removing the wheel.

4: Align the adjusting access slot in the brake drum

with the adjusting star wheel at the bottom of the

brake.

5: While rotating the brake drum back and forth,

rotate the brake adjuster star wheel until the

brake is tight enough so that brake drum cannot

be rotated.

6: Back off the star wheel just enough so that the

brake drum rotates freely.

7: Install the tire/wheel assembly.

8: Repeat this procedure for the opposite side

brake.

9: Set the park brake.

10: Reconnect the main positive and negative cables

at the batteries.

11: Remove blocks from behind the wheels.

12: Release the park brake and test drive the vehicle.

Adjust the Service Brake Linkage

Do not use this procedure to adjust the brakes. This

procedure should only be performed when replacing

any of the mechanical brake linkages or cables or it is

found that the cables or linkages have been adjusted

incorrectly.

1: Release the park brake.

2: Loosen the clevis jam nuts on the main brake

cable and connecting rod.

3: Loosen the brake cable and connecting rod.

4: Adjust the park brake linkage so that the angle

between the connecting rod and the cross shaft

tab is at 60 degrees.

5: Tighten the brake cable so that all slack is

removed from the cable, but not so much so that

the cross shaft rotates.

6: Tighten the connecting rod so that all slack is

removed from the brake cables, but not so much

as to actuate the brakes.

7: Tighten the jam nuts on the brake cable,

connecting rod, and park brake linkage.

8: Set the park brake.

9: Reconnect the main positive and negative cables

at the batteries.

10: Remove blocks from behind the wheels.

11: Release the park brake and test drive the vehicle.

Parking Brake, Mechanical Brakes

Trucks equipped with mechanical drum brakes do not

have a separate adjustment for the parking brake. If

the parking brake requires adjustment, then the entire

brake system is in need of adjustment. Refer to

Adjust

the Service Brake

section for information regarding

adjusting the brakes.

Adjusting the brakes by means of the brake cables

could cause a hard brake pedal with little or no

braking power. This could cause loss of control of

the vehicle resulting in severe bodily injury and /or

property damage.

WARNING

Brake linkage with protractor in place

at 60 degrees

Содержание B0-200-00





























































































































































































Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды

Taylor-Dunn B0-200-00, Инструкция по обслуживанию и замене запасных частей

Результаты поиска

Содержание B0-200-00

Отзывы:

Похожие инструкции для B0-200-00

Бренды по названию

Популярные бренды