Tascam PA-R100, Инструкция по эксплуатации

Страница: 50 / 96

Advanced Operations
En-50
Main menu Speaker Setup
Here you can check the settings made by Audyssey 2EQ
Room Correction and Speaker Setup function, or set them
manually, which is useful if you change one of the
connected speakers after using Audyssey 2EQ Room
Correction and Speaker Setup function.
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “
Full Band ” for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies.
■
Subwoofer
`
Yes
`
No
■
Front
`
Full Band
`
40Hz , 45Hz , 50Hz , 55Hz , 60Hz , 70Hz , 80Hz , 90Hz ,
100Hz , 110Hz , 120Hz , 130Hz , 150Hz , 200Hz
Note
• If the “ Subwoofer ” setting is set to “ No ”, the “ Front ” setting is
fixed at “ Full Band ”.
■
Center
*1
, Surround
*1
`
Full Band
`
40Hz , 45Hz , 50Hz , 55Hz , 60Hz , 70Hz , 80Hz , 90Hz ,
100Hz , 110Hz , 120Hz , 130Hz , 150Hz , 200Hz
`
None
■
Front High
*1*2*4
`
Full Band
`
40Hz , 45Hz , 50Hz , 55Hz , 60Hz , 70Hz , 80Hz , 90Hz ,
100Hz , 110Hz , 120Hz , 130Hz , 150Hz , 200Hz
`
None
■
Surround Back
*1*2*3
`
Full Band
`
40Hz , 45Hz , 50Hz , 55Hz , 60Hz , 70Hz , 80Hz , 90Hz ,
100Hz , 110Hz , 120Hz , 130Hz , 150Hz , 200Hz
`
None
Note
*1 “ Full Band ” can be selected only when “ Full Band ” is
selected in the “ Front ” setting.
*2 If the “ Surround ” setting is set to “ None ”, this setting cannot
be selected.
*3
If anything else than “ None ” is selected in “ Front High ”, this
setting is automatically set to “ None ”.
*4 If anything else than “ None ” is selected in “ Surround Back ”,
this setting is automatically set to “ None ”.
■
Surround Back Ch
`
1ch :
Select if only one surround back speaker L is
connected.
`
2ch :
Select if two (left and right) surround back speakers
are connected.
Note
• If the “ Surround Back ” setting is set to “ None ”, this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)
`
80Hz , 90Hz , 100Hz , 110Hz , 120Hz
`
Off :
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency of
the LFE channel’s low-pass filter (LPF), which can be
used to filter out unwanted hum. The LPF only applies to
sources that use the LFE channel.
■
Double Bass
`
On
`
Off
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to
the subwoofer.
Note
• When the “ Subwoofer ” setting is set to “ No ” or the “ Front ”
setting to anything other than “ Full Band ”, this setting is fixed to
“ - - - ”.
• This setting is set to “ On ” automatically when the “ Subwoofer ”
and “ Front ” settings are set for the first time to “ Yes ” and “ Full
Band ” respectively.
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey 2EQ
® Room Correction and Speaker Setup
(
➔
page 32
).
This setting is set automatically by Audyssey 2EQ Room
Correction and Speaker Setup (
➔
page 32
).
1 2 3 4 5
“ Setup ”
This setting is NOT set automatically by Audyssey 2EQ
Room Correction and Speaker Setup (
➔
page 32 ).