Tascam DR-701D, Справочное руководство

Страница: 40 / 46

40
TASCAM DR-701D
11 – Messages
The following is a list of the pop-up messages.
Refer to this list if one of these pop-up messages appears on the
DR-701D and you want to check the meaning or determine a
proper response.
Message Meaning and response
Battery Empty
The batteries are almost out of power.
Replace the batteries.
Card Error
The SD card could not be recognized
properly. Change the card.
Card Full
The SD card has no remaining space.
Erase unnecessary files or move them to
a computer to make open space.
File Full
The total number of folders and files
exceeds the limit of 5000. Erase unnec-
essary folders and files or move them to
a computer.
File Not Found
A file cannot be found or a file might be
damaged. Please check that file.
File Not Found
Make Sys File
The system file is missing. This unit
requires a system file for operation.
When this message appears, press the
DATA dial to automatically create a
system file.
File Protected
The file is read only and cannot be
erased.
Format Error
Format CARD
The SD card is not formatted properly
or the card is broken. This message also
appears if the card was formatted using
a computer connected by USB or if an
unformatted card is inserted in the unit.
Always use the DR-701D to format cards
to be used with it. Change the card or
press the DATA dial while this message
is being shown to format the card.
Formatting will erase all the data on the
SD card.
Invalid Card
Change Card
Something might be wrong with the SD
card. Change the SD card.
Invalid SysFile
Make Sys File
The system file required to operate
this unit is invalid. When this message
appears, press the DATA dial to
automatically create a new system file.
Layer too Deep
Folders can be created down to two
layers. You cannot create a new folder
inside the current folder.
MBR Error Init CARD
The SD card is not formatted properly or
the card is broken. Change the card or
press the DATA dial while this message
is being shown to format the card.
Formatting will erase all the data on the
SD card.
No Card
No SD card is loaded in the unit. Insert a
recordable SD card.
No PB File
There is no file that can be played back.
The file might be damaged.
Non-Supported
The audio file is not a supported format.
Please see “8 – Connecting with a
Computer” on page 35 for file formats
that this unit can use.
Switched To Internal
Battery
The power source has switched from
USB bus power to the batteries in the
unit.
Write Timeout
Writing to the SD card timed out.
Backup files on the card to a computer,
and format the card.
No Rec Channels
Selected
No recording channels have been
selected (all are off).
Message Meaning and response
HDMI CONNECTED
LOCK to HDMI.
HDMI is connected.
The clock master will switch to HDMI.
HDMI DISCONNECTED
LOCK to INTERNAL
HDMI became disconnected.
The clock master will switch to internal.
-HDMI CONNECTED-
Mismatch
Audio Clock.
Change to **kHz?
HDMI is connected.
The sampling frequency is different. Do
you want to change it?
Fs Mismatch
LOCK to INTERNAL.
The sampling frequency was changed.
The clock master will switch to internal.
Fs Match
LOCK to HDMI.
The sampling frequency was changed.
The clock master will switch to HDMI.
Can't Save Data
If any of these errors occurs, turn the
unit off and restart it.
If the power cannot be turned off,
remove the batteries, disconnect the
AC adapter (TASCAM PS-P515U; sold
separately), and/or disconnect the USB
cable if used for USB bus power supply.
If these error messages continue to
appear frequently, please contact a
TEAC Repair Center (see back cover).
Device Error
File Error
Not Continued
Player Error
Remote Cmd
Remote Rx
Writing Failed
Sys Rom Err
System Err 50
System Error 1
System Error 2
System Error 3
System Error 4
System Error 5
System Error 6
System Error 7
System Error 8
System Error 9