Tanda AQUATOP Скачать руководство пользователя страница 9

Страница: 9 / 239

MAN-AT-A2-1

Manual Aquatop (2019)

A2-1 - Constructional preparations: Underwater mount - In niche

General:

•

Level control is necessary to install and use an automatic slatted cover. Provide an
overflow and a refilling system to guarantee the correct level in case of a skimmer
pool.

•

Do not place any obstacles in the back or side walls which can interfere with the slats.
For example: skimmer covers, ladders, etc…

•

Roman ends, rectangular ends and other particular shapes cannot always be rolled up
completely.

•

To comply with the European standard EN_16582-1/2/3, you need to cover the rollo
cover pit.

Concept:

•

The Rollo cover is integrated in a niche behind the pool.

•

The roller needs to be minimum 3cm under the water level.

•

Drive: external electric, external hydraulic or in-roller motor.

Options:

•

SCUBA-drive® plates avoid the use of wall duct.

•

See chapter “

O2 – Finishing: Underwater mount – In niche / in pool

”

•

The niche can be covered with wooden or plastic

gratings

in combination with a beam

or adjustable brackets.

•

Coverwash®

system can be installed at the backside of the beam.

Target values:
(Valid for pools till 6m width – exact diameter can be found on the quotation of T&A
and the first page of the manual of each project)

* On demand

Cover length (m) (stairs incl.)

Diameter (

) Rollo cover ( mm)

Slat dimension : 60 x 14 mm

420

480

520

580

610

640

705

780

Diameter (

) Rollo cover ( mm)

Slat dimension : 67,5 x 16,5 mm

440

500

540

600

640

680

720

820

SCUBA wall plates can be used?

YES

Содержание AQUATOP
















































































































































































































































Результаты поиска

Содержание AQUATOP

Отзывы:

Tanda AQUATOP, Руководство по установке, Страница: 9 / 239

Результаты поиска

Содержание AQUATOP

Отзывы: