Tanda AQUATOP Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 239

Tanda AQUATOP Скачать руководство пользователя страница 70

MAN-AT-C5-2

Manual Aquatop (2019)

1

C5-2 – Mounting of mechanism: Underwater mount: SCUBA-drive® with

cable duct with thin wall (Mono block or element pool)

General:

•

The SCUBA-drive® tubular motor is being delivered with a 10m long motor cable, connected
to the motor.

•

Bring the motor cable outside the swimming pool, above water level, through a conduit to a
connection box.

•

This connection box must be accessible at all times, so the motor can be demounted during
maintenance.

•

It is extremely important to use the supplied polyester resin in the connection box in order to
avoid water damage to motor and/or control box. In case the supplied resin is not used;
warranty will be void.

•

we strongly recommend to use our cable connection kit (see AT-MAN-B4 : Electrical
preparations)

•

In case of a composite pool or a pool made out of plastic (PP, PE) we recommend to connect
the outside stainless steel flanges to the earth to avoid galvanic corrosion.

1. Installation of the flanges

•

Mount the flange and anchor it with bolts through the wall. Mount the motor flange over the
hole and anchor it with bolts through the wall. Don’t forget the flat sealings!

•

See chapter “

A7 – Constructional preparations: Cable duct for SCUBA-drive®

”

2. Installation of the roller shaft

•

Push the roller shaft on to the shaft end at the flange. Do not tighten the setting ring with the
screws too much at this moment. Always grease the bearings using Vaseline.

•

Put the motor in the motor flange and anchor it. Make sure the motor cable doesn’t get
damaged during conducting through.

•

Fasten the setting ring with the screws on the flange, but leave a space of 5mm between the
roll-up shaft and the setting ring. In this way the shaft will not get jammed in case of
expansion.

Alternatively; a cable
gland can be used at
this position, as such
there is no water in
the conduit.
Art. no. AT-002883

Before installing the shaft, remove the grey cable
guard.
Make sure that the cable is not damaged by the
stainless steel during this operation.

«
...
68
69
70
71
72
...
»

Содержание AQUATOP
















































































































































































































































Отзывы:

Нет отзывов