Tanda AQUATOP Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 239

Tanda AQUATOP Скачать руководство пользователя страница 59

MAN-AT-C3

Manual Aquatop (2019)

1

C3 – mounting of mechanism: Underwater mount: External motor – Pool with

thin wall

General:

•

Install the bearing blocks and the flange before filling up the pool.

•

Use water seal rings to assure the water tightness.

1. Installation of the bearings

•

Mark and drill holes (Ø7mm) for the bearing block. Use the flat sealing as a drawing
mould.

•

Drill the wall duct hole of Ø35mm in the centre (120-250-500 Nm) or Ø42mm (1000
Nm)

•

Place the water seal rings in the bearing blocks with the open side of the ring facing
the pool. The ring must be positioned 100% in line/sunk.

•

Bolt the pool wall between the pool bearing block and the outer bearing at the outside
of the pool. Put flat sealings between the bearing block and the wall at both sides of
the pool wall.

•

In case of a composite pool or a pool made out of plastic (PP, PE) we recommend to
connect the outside stainless steel flange to the earth to avoid galvanic corrosion.

2. Installation of the flange

•

Mark and make the boring holes (Ø7mm) for the flange in the wall. Use the flat
sealing as a drawing mould.

•

Bolt the pool wall between the flange and the outer flange with blind holes. Put flat
sealings between the flange and the wall at both sides of the pool wall.

«
...
57
58
59
60
61
...
»

Содержание AQUATOP
















































































































































































































































Отзывы:

Нет отзывов