212
Chapter
5
Replacement Procedures
Installation Using The Short Tip Alignment Tool
This procedure is for installing one hammer spring assembly at a time, using
short the tip alignment tool that comes with version 2 replacement hammer
spring. To install more than one hammer spring assembly at a time, you must
use the long tip alignment tool (page 214).
1.
Using a clean dry cloth, wipe the hammer spring mounting surface on the
hammer bank. Make sure the cloth does not leave lint on the hammer
bank.
CAUTION
Hammer springs and hammer tips are fragile. Do not touch the hammer
springs or tips. Handle hammer springs by the thick mounting base
only. Apply pressure only to the mounting base.
2.
Handling the hammer spring assembly by the mounting base only,
remove the new assembly and mounting screws from the box.
3.
Handling the hammer spring assembly by the mounting base, position it
on the hammer bank and center it over the mounting screw holes.
(See Figure 26.)
4.
Position the tip alignment tool over the end hammer tips of the new
hammer spring and the end hammer tips of the adjacent hammer springs
used for alignment. Use the guide tool to maneuver the hammer tips into
the alignment tool. (See Figure 26.)
Figure 26. Installing a Version 2 Hammer Spring Assembly Using the Short Alignment Tool
184083a
Tip Alignment Tool
New Hammer
Spring Assembly
Hammer Spring
Used For Alignment
Guide Tool
Hammer Spring
Used For Alignment
NOTE
: A 6615 lpm version 2 hammer bank is
shown here. Removal, installation, and fastener
torque values are the same for all version 2
hammer spring assemblies, even though
hammer spring assemblies vary in number of
hammers and number of mounting screws.
Models -05
: Tool 253258-001
Models -10: Tool 253257-001
Models -15: Tool 253256-001
Models -20: Tool 253255-001
Содержание 6600 Series
