TAC Xenta 555 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 82

TAC Xenta 555 Скачать руководство пользователя страница 23

TAC Xenta 555, Supplement Manual

3 Commissioning the TAC Xenta 555

TAC AB, Oct 2006

23 (82)

04-00054-01-en

3

Commissioning the TAC Xenta 555

There are six basic steps to commissioning the Xenta 555. These steps
are described below.

To commission the TAC Xenta 555

1

Connect the Xenta 555 to 24 VAC power.

Refer to

TAC Xenta 555 Installation Instructions

(0FL-3956-005)

for instructions.

2

Connect a PC to the Xenta 555’s serial port.

Attach a serial cable from the computer’s COM port to the
RS232 B port on the front of the Xenta 555. Refer to

511/527/555/911/913, Product Manual

for complete instructions.

3

Set the Xenta 555’s communication parameters.

Before the Xenta 555 can successfully communicate on the Ether-
net, you must first set its IP address and other basic parameters.
Refer to

TAC Xenta 511/527/555/911/913, Product Manual

complete instructions.

4

Connect the Xenta 555 to the Ethernet network.

Attach the Xenta 555 to the network at the necessary location.
Refer to Chapter 4, “Connecting the TAC Xenta 555 to Your Net-
work”, on page 25 for more information.

5

If necessary, load the Xenta 555’s software.

The Xenta 555 is delivered from the factory with pre-loaded soft-
ware. If you need to reload this software, you can download it from
TAC’s website (http://delphi.tac-global.com). Before installing
downloaded software, review its release information to verify com-
patibility with your hardware. Refer to

TAC Xenta 511/527/555/

911/913, Product Manual

for complete instructions.

6

Configure the Xenta 555 to communicate with MicroNet/Satchnet
controllers.

In order for the Xenta 555 to communicate with MicroNet devices
from across an Ethernet network, you may need to define some
basic communication parameters. Refer to Chapter 6, “Setting Up

Caution

Ensure correct polarity at all 24 VAC devices.

«
...
21
22
23
24
25
...
»

Содержание Xenta 555



















































































Отзывы:

Нет отзывов