TA Instruments RSA-G2 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 127

background image

RSA-G2 Getting Started Guide

Page 31

Chapter: 2

Installing the RSA-G2

Unpacking/Repacking the RSA-G2

The instructions needed to unpack and repack the instrument are found as separate unpacking instructions

in the shipping box and in the online documentation associated with the instrument control software. You

may wish to retain all of the shipping hardware, the pallet, and boxes from the instrument in the event you

wish to repack and ship your instrument.

Preparing the System

Before shipment, the RSA-G2 DMA is inspected both electrically and mechanically so that it is ready for

operation upon proper installation. Only limited instructions are given in this manual; consult the online

documentation for additional information. Installation involves the following procedures:
• Inspecting the system for shipping damage and missing parts.
• Choosing a suitable location.
• Connecting the RSA-G2 to a suitable air supply.
• Connecting all cables and lines.
• Connecting the RSA-G2 to the customer line voltage outlet.
• Connecting the RSA-G2 to the controller computer and network.

CAUTION: It is recommended that you have your RSA-G2 unpacked and installed by a TA Instru

-

ments Service Representative. Call for an installation appointment when you receive your instru

-

ment.

MISE EN GARDE: Il est recommandé que le dépotage et l'installation de votre RSA-G2 soient

assurés par un représentant du service d'entretien de TA Instruments. Appelez pour prendre ren

-

dez-vous en vue d'une installation à la réception de votre instrument.

Inspecting the System

When you receive your RSA-G2, look over the instrument and shipping container carefully for signs of

shipping damage, and check the parts received against the enclosed shipping list.
• If the instrument is damaged, notify the carrier and TA Instruments immediately.
• If the instrument is intact but parts are missing, contact TA Instruments.

«
...
59
60
61
62
63
...
»

Содержание RSA-G2
































































































































Отзывы:

Нет отзывов

Похожие инструкции для RSA-G2

Бренд: Hagie Страницы: 61

Бренд: Yamaha Страницы: 78

Бренд: Fast Страницы: 42

Бренд: DARAY Страницы: 28

Бренд: Haenim Страницы: 2

Бренд: CAMPAGNOLA Страницы: 4

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Бренд: Keithley Страницы: 79

Бренд: Kayakpro Страницы: 17

Бренд: Yoshitake Страницы: 11

Бренд: National Instruments Страницы: 10

Frontier FC5706

Бренд: OHAUS Страницы: 47

Бренд: Ocutech Страницы: 4

Бренд: Yamaha Страницы: 31

TOTAL KNEE 1900

Бренд: Össur Страницы: 58

Бренд: Aveo Engineering Страницы: 16

Бренд: Petromax Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды