System Q SEEK200 Скачать руководство пользователя

Страница: 71 / 92

Video Recording and Picture Capture

Network Settings

13.1 TCP/IP

TCP/IP settings must be properly configured before you operate the device over network.
IPv4 and IPv6 are both supported. Both versions can be configured simultaneously without
conflicting to each other.
Go to

Configuration

Basic Configuration

Network

TCP/IP

for parameter

settings.

NIC Type

Select a NIC (Network Interface Card) type according to your network condition.

IPv4

Two IPv4 modes are available.

DHCP

The device automatically gets the IPv4 parameters from the network if you check

DHCP

. The device IP address is changed after enabling the function. You can use a

network search tool to get the device IP address.

Note

The network that the device is connected to should support DHCP
(Dynamic Host
Configuratio
n Protocol).

Manual

You can set the device IPv4 parameters manually. Input

IPv4 Address

IPv4 Subnet

Mask

, and

IPv4 Default Gateway

, and click

Test

to see if the IP address is available.

IPv6

Three IPv6 modes are available.

Route Advertisement

The IPv6 address is generated by combining the route advertisement and the device
Mac address.

Содержание SEEK200





























































































Результаты поиска

Содержание SEEK200

Отзывы:

Похожие инструкции для SEEK200

Бренды по названию

Популярные бренды

System Q SEEK200, Инструкция по эксплуатации

Результаты поиска

Содержание SEEK200

Отзывы:

Похожие инструкции для SEEK200

Бренды по названию

Популярные бренды