background image

STEP 5

ATTACHING THE TINE HEIGHT ADJUSTMENT BAR

See 

STEP 5

 photo before proceeding

1.  Locate the tine height adjustment bar and fasten to the center support 

of the tine bar assembly using the 1/2” x 1 1/2” bolt & lock nut 

STEP 5

 

photo. 

2.  Lift and attach the other end to the center hole of the tine height adjust-

ment bracket attached to the under side of the A-frame using one of the 

5/8” x 4 1/2” hitch pins and secure in place with the cotter pin.

STEP 6

FINALIZING BLADE POSITION

See 

STEP 6

 photo before proceeding

1.  Lift the blade from either side until the center blade pitch angle adjust-

ment  hole  is  lined  up  with  the  hole  in  the  blade  post.  Then  secure  in 

position with the remaining 5/8” x 4 1/2” hitch pin.

ATTACHING THE TRACK AND RING CONDITIONER USING THE 3 POINT 

HITCH ASSEMBLY

STEP 6

ATTACHING TO THE TRACTOR

1.  Backup your tractor with a 3 point hitch to the Track Conditioner. Make 

sure the area is clear of people and animals.

2.  Position the tractor so the lift arms line up with the lift pins on the con-

ditioner.

3.  Slide the lift arms over the lift pins and put on the clip pins.

4.  Attach the top link supplied with your tractor to top of the three point 

hitch with the hitch pin supplied.

5. Adjust to the top link until the "A" Frame of the conditioner is level.

See operation instructions on last page for proper use of your Track and 

Ring Conditioner.

TINE HEIGHT ADJUSTMENT

A-frame

L-shaped 

draw pin

Center sup-

port tine bar 

assembly

Tine height 

adjustment 

bar

Tine height adjustment 

bracket

STEP 5

BLADE POSITION

Blade pitch angle 

adjustment holes

5/8” x 4 1/2” 
hitch pin

3/4” x 5” bolt 

and nut

1/4” angle iron 

for strength 

and durability

Blade

Blade angle 

adjustment pin

Blade post

STEP 6

Содержание TRC-6









Отзывы: