background image

STEP 3

ATTACHING THE 3 POINT HITCH

See 

STEP 3

 photo before proceeding

1.  First fasten the straight bar to the A-frame with a 1/2"x 1 1/2" bolt & lock 

nut 

FIG 3A

.

2.  Then locate and fasten the two S-shape hitch bars to the A-frame with 

the lift pins as shown 

FIG 3B

.

3.  Now take the unfastened ends of the S-shaped bar and straight bar and 

using the 1/2” X 4” bolt & nut with the 1" spacers on either side of the 

straight bar join the 3 ends as shown in 

FIG 3C

.

4.  Tighten these bolts now before proceeding.

5.  Then install the hitch pin and fasten with the cotter pin.

NOTE:

  There will be approximately 1/4” of play around the hitch pin this 

is normal.

STEP 4

ATTACHING THE TINE BAR ASSEMBLY TO THE A-FRAME

See 

STEP 4

 photo before proceeding

1.  Support  the  front  of  the  A-frame  at  an  approximate  height  of  14”  to 

16” (we used two 5 gallon buckets) place the buckets or whatever you 

choose under the 3 point hitch brackets at the front of the A-frame 

FIG 

4A

.

NOTE:

  Keep supports clear of A-frame. 

IMPORTANT:

 make sure A-frame is 

supported securely.

2.  Now slide the tine bar assembly into position under the A-frame with the 

tines pointing down and towards the blade at the back. 

FIG 4B

3.  With help attach the tine bar assembly with the 5/8” x 2” bolts & lock 

nuts to the 3 mounting brackets on the under side of the A-frame.

4.  Tighten  the  bolts  and  back  off  1/4  turn  to  allow  tine  bar  assembly  to 

move freeely.

3 POINT HITCH ASSEMBLY

1” spacers

1/2” x 4” bolt and nut

A-frame

Straight 

bar

S-shaped bar

Lift pin

Lift pin

S-shaped bar

STEP 3

1” spacers

Straight bar

Hitch pin

1/2” x 4” 

bolt and nut

S-shaped bar

S-shaped bar

FIG 3C

A-frame

FIG 3A

Lift pin

FIG 3B

TINE BAR TO A-FRAME

A-frame

Tine bar 

Assembly 

brackets

Tine bar Assembly

STEP 4

A-frame

FIG 4A

14”

16”

A-frame

FIG 4B

Tine Bar 

Assembly

Blade

14”-16”

5 gal.buckets

Tine Bar 

Assembly 

connection 

points

NOTE:

  Tine bar needs to swing freely from A-frame connection points. 

Tighten the bolts and back off each bolt 1/4 turn or until tine bar 

assembly moves freely.

5 gal.buckets

1/2” x 1 

1/2” bolt 

and nut

Straight 

bar

A-frame

S-Shaped 

bar

Содержание TRC-6









Отзывы: