Synxcom SM9234D Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 216

Synxcom SM9234D Скачать руководство пользователя страница 56

AT Commands

Page 56

modem firmware (data) to the host computer. Uploading new firmware to the flash
memory or downloading existing firmware from the flash memory device is a two-
step process

When the AT** command is issued, the modem firmware boot loader is invoked
and the user will first load a flash load module (FLM) into the modem's RAM. If
the user wishes to upload new firmware to the modem, he should load the
uploader FLM. If the user wishes to download existing firmware from the modem,
he should load the downloader FLM. In either case, the data transfer is done via an
ASCII transfer. The FLM contains the programming algorithm for the flash
memory device being programmed and any messages that may be sent during the
load process.

If the user wishes to upload new firmware to the modem, then he will then load the
new modem firmware which the uploader FLM will then program into the flash
memory device. This transfer is done via XMODEM transfer. If the user wishes to
download existing firmware from the modem, then he will set up the host PC for
XMODEM receive and the downloader FLM will begin to send the existing
firmware from the flash memory to the host PC.

Procedure

1.

Install in the modem a flash memory programmed with the modem firmware or
a blank flash memory.

2.

Put the uploader FLM and downloader FLM files and the new modem
firmware file (e.g., XmUL003.s37, XmDL003.s37, and 206s4712.S37) in an
appropriate directory on the computer's hard disk.

3.

Configure the communications application program for a DTE rate of between
9600 bps and 115200 bps and RTS/CTS flow control.

4.

Check the modem for response by typing AT.

5.

Initiate the download process using the AT** command. The "Download
flash code…" message appears upon issuing the AT** command.

6.

Perform an ASCII transfer of the FLM file (e.g., XmUL003.s37 for uploading
new firmware to the modem or XmDL003.s37 for downloading existing
firmware from the modem) from the host computer to the modem RAM using

«
...
54
55
56
57
58
...
»

Содержание SM9234D

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды