Synxcom SM9234D Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 216

Synxcom SM9234D Скачать руководство пользователя страница 102

AT Commands

Page 102

1 Decimal number which enables/disables issuance

of +A8x indications during modem-controlled V.8
answer negotiation.

5 Enable DCE-controlled V.8 answer negotiation with

+A8x indications.

<v8cf Set the V.8 CI signal call function to the hexadecimal octetXY.

00 (Default.)

21

C1

<v8b> Decimal number which enables/disables V.8bis negotiation.

0 Disable V.8bis negotiation.

1 Enable V.8bis negotiation. (Default.)

<cfrange> “<string of values>“. Applicable only for <v8a>=5. Not

supported.

< protrange > “<string of values>“. Applicable only for <v8a>=5. Not

supported.

Default values: 1,1,00,1,0,0
The ATD and ATA commands behave as specified in V.250, and +A8n indications
are not generated by the modem.
For subparameter values <v8o>=6 and <v8a>=5, the +A8I indications are issued
during the course of the V.8 session to notify the DTE when the relevant V.8
signals are received.
Reporting Current or Selected Values
Command:

+A8E?

Response:

+A8E:
<v8o>,<v8a>,<v8cf>[,<v8b>][,<cfrange>][,<protrange>]

Example:

+A8E: 1,1,00,1,0,0 For the defaults

Reporting Supported Range of Parameter Values
Command:

+A8E?

Response:

+A8E: (<v8o> range),(<v8a> range),(v8cf in octets), (<v8b>
range),(<cfrange>),(<protrange>)

Example:

+A8E: (1,6),(1,5),(0,21,C1),(0,1),(0),(0)

+A8I: - CI Signal Indication

This indication is issued by an answering modem, if +A8E,<v8a> 0, to indicate
detection of a V.8 CI signal, and report the recovered Call Function octet(s).

Indication
Syntax

+A8I:<v8cf><CR>

Defined Value

<v8cf>

A hexadecimal code octet representation of those Call Function
octet(s). +A8I:0 indicates that the modem timed out waiting for
CI.

Example

+A8I:0 The modem timed out waiting for CI.

+A8I:X YYY

«
...
100
101
102
103
104
...
»

Содержание SM9234D

























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды