Synxcom SM9234D Скачать руководство пользователя страница 208

Страница: 208 / 216

AT Commands

Page 208

+VSM - Compression Method Selection

This command causes the modem to set the voice compression method, the silence
compression sensitivity, and the voice sampling rate.

Reporting Supported Range of Parameter Values

Syntax

+VSM=<cml>,<vsr>,<sds>,<sel>

Defined Values

<cml>

Decimal number identifying the compression method.

<vsr>

<range of values> containing the supported range of voice
samples per second of the analog signal.

<scs>

<range of values> containing the supported range of sensitivity
settings for voice receives.

<sel>

<range of values> containing the supported range of expansion
values for voice transmits.

Reporting Current or Selected Values
Command:

+VSM?

Response:

Example:

1,8000,0,0

For the default setting.

Reporting Supported Range of Parameter Values
Command:

+VSM=?

Response:

<cml> Decimal number identifying the compression

method (1, 129, 130, 140, or 141).

<cmid> Alphanumeric string describing the compression

method (UNSIGNED PCM, IMA ADPCM,
UNSIGNED PCM, 2 Bit ADPCM, or 4 Bit
ADPCM).

<bps> Decimal number defining the average number

of bits in the compressed sample not including
silence compression (2, 4 or 8).

<tm> Decimal number (0) reporting the time interval,

in units of 0.1 second, between timing marks. A
value of 0 reports that timing marks are not
supported.

<vsr> <range of values> containing the supported

range of voice samples per second of the
analog signal (8000).

<scs> <range of values> containing the supported

range of sensitivity settings for voice receives
(0). A 0 indicates not supported.

<sel> <range of values> containing the supported

range of expansion values for voice transmits
(0). A 0 indicates not supported.

Example:

1,"UNSIGNED PCM",8,0,8000,0,0
129,"IMA ADPCM",4,0,8000,0,0
130,"UNSIGNED PCM",8,0,8000,0,00
140,"2 Bit ADPCM",2,0,8000,0,0
141,"4 Bit ADPCM",4,0,8000,0,0
OK

Result Codes

OK Valid range.

Содержание SM9234D

























































































































































































































Результаты поиска

Содержание SM9234D

Отзывы:

Бренды по названию

Популярные бренды

Synxcom SM9234D, Руководство пользователя

Результаты поиска

Содержание SM9234D

Отзывы:

Бренды по названию

Популярные бренды