Synxcom SM9234D Скачать руководство пользователя страница 163

Страница: 163 / 216

AT Commands

Page 163

Response:

Example 1:

For automatic rate detection.

Example 2:

For 57600 bits/s.

Reporting Supported Range of Parameter Values
Command:

+FPR=?

Response:

(<rate code> range)

Example:

(0,1,2,4,8,10,18)

+FMI? - Request Manufacturer Identification

This command causes the modem to report the modem product manufacturer.

Syntax

+FMI?

Typical Response

CONEXANT
OK

+FMM? - Request Model Identification

This command causes the modem to report the modem product model.

Syntax

+FMM?

Typical Response

V90
OK

+FMR? - Request Revision Identification

This command causes the modem to transmit one or more lines of information text
identifying the modem version, revision level or date.

Syntax

+FMR?

Typical Response

V3.001-V90_2M_DLS
OK

+FLO - Flow Control

This parameter allows the DTE to identify and select the type of flow control used.

Syntax

+FLO=<method>

Defined Values

<method> Decimal number corresponding to the selected option.

0 XON/XOFF and RTS/CTS flow control turned off.

1 Use XON/XOFF flow control in either direction.

2 Use RTS for flow control of the modem by the DTE;

use CTS for flow control of the DTE by the modem.

Reporting Current or Selected Values
Command:

+FLO?

Response:

+FLO<method>

Example

+FLO: 0

For the default setting.

Reporting Supported Range of Parameter Values

Содержание SM9234D

























































































































































































































Результаты поиска

Содержание SM9234D

Отзывы:

Бренды по названию

Популярные бренды

Synxcom SM9234D, Руководство пользователя

Результаты поиска

Содержание SM9234D

Отзывы:

Бренды по названию

Популярные бренды