manualshive.com logo in svg

Swagelok VCM, Руководство пользователя, Страница: 6 / 20

Поделиться
Скачать
Swagelok VCM Скачать руководство пользователя страница 6

6

     

Valve Control Module

 User’s Manual

Control Drawing

Fig. 3  VCM-DN-0011 SCHEDULE

4

5

3

2

1

1, 4, 7, 11, 14, 17: Sensor V+

2, 5, 8, 12, 15, 18: Sensor Response

3, 6, 9, 13, 16, 19: Sensor V-

10, 20: No Connect

Notes:

(1)  The Entity Concept allows interconnection of nonincendive apparatus with  associated apparatus not specifically examined in combination as a system when the  approved values of Voc and Isc of the associated apparatus are less than or equal to  Vmax and Imax of the nonincendive apparatus and the approved values of Ca and  La of the associated apparatus are greater than Ci+Ccable and Li+Lcable respectively  for the nonincendive apparatus.

(2) Capacitance and inductance of the field wiring from the nonincendive equipment  to the associated apparatus shall be calculated and must be included in the system  calculations as shown in Table 1.  Cable capacitance, Ccable, plus nonincendive  equipment capacitance, Ci, must be less than the marked capacitance (Lcable, Li  and La or Lo, respectively).  Where the cable capacitance per foot are not known, the  following values shall be used:  Ccable = 60 pF/ft., Lcable = 0.2 

µ

H/ft.

TABLE 1:

                                        

TABLE 2:

                                   

TABLE 3:

Nonincendive Equipment

          

Associated Apparatus

          

Sensor Interface

V max (or Ui) 

≥

                             Voc (or Uo)                             Voc (or Uo)

I max (or Ii) 

≥

                                 Isc (or lo)                                 Isc (or lo)

P max (or Pi) 

≥

                              Po                                             Po

Ci  

≤

                                               Ca (or Co)                              Ca (or Co)

Li  

≤      

                                 La (or Lo)                                La (or Lo)

If Po of the associated apparatus is not known, it may be calculated using the formula:  Po = (Voc * Isc)/4 = (Uo * Io)/4.

(3) Associated apparatus must be installed in accordance with its manufacturer's  control drawing and Article 504 of the National Electrical Code (ANSI/NFPA 70), the  Canadian Electrical Code, or other local installation codes, as applicable.  The  resistance of the ground path must be less than 1 ohm.

(4) When required by the manufacturer's control drawing, the associated apparatus  must be connected to a suitable ground electrode per the National Electrical Code  (ANSI/NFPA 70), the Canadian Electrical Code, or other local installation codes, as  applicable.  The resistance of the ground path must be less than 1 ohm.

(5) The VCM is powered by two separate nonincendive circuits, designated Power and  Signal as indicated in Tables 1, 2 and 3.  Cable and wiring for these two circuits must  maintain the separations for different nonincendive circuits required by Article 504 of  the National Electrical Code (ANSI/NFPA 70), ISA RP12.6 for installing nonincendive  circuits, or other local codes, as applicable.

(6) Associated apparatus must not be used in combination unless permitted by  associated apparatus certification.               

(7) WARNING:  Substitution of components may impair safety.

(8)  The ambient operating (Tamb) range for this product is -5C to 50C.

(9) 

Each unit must be connected to an IP64 or higher rated connector or IP rating will be void.

HAZARDOUS LOCATION

Class I, Div. 2, Groups C, D

Any associated apparatus power  supply with Entity Concept  Parameters (1) appropriate for  connection to an nonincendive  device with Entity concept  parameters listed in Table 1.

Any nonincendive or associated  apparatus communication  controller with Entity Concept  parameters (1) (Vmax, Imax, Ci,  Li) appropriate for connections to  nonincendive devices with Entity  Concept parameters listed in  Table 1.

NON-HAZARDOUS LOCATION

CONTROL EQUIPMENT

NONINCENDIVE FIELD WIRING - POWER CIRCUIT (PINS 2,3)

NONINCENDIVE FIELD/ ASSOCIATED APPARATUS WIRING - SIGNAL CIRCUIT (PINS 4,5)

Field Wiring Diagram

1 - Drain       bare 2 - V+            red 3 - V-             black 4 - CAN_H    white 5 - CAN_L     blue

WARNING: ANY CHANGES MADE TO THIS DOCUMENT MUST BE REVIEWED AND APPROVED BY SWAGELOK COMPLIANCE DPT

MATERIAL: NA

DESCRIPTION: SWAGELOK DEVICENET PTX CONTROL DRAWING

Male

Sensor Interface

DWG. NO.

VCM-DN-0011-SCHEDULE

TITLE

DRAWN BY

CHECK/APR BY

JEK

DWG. NO.

VCM-DN-0011-SCHEDULE

THIS PRINT IS THE EXCLUSIVE PROPERTY OF SWAGELOK COMPANY.  IT MUST BE RETURNED ON  REQUEST ALONG WITH ANY DOCUMENTS CONTAINING INFORMATION OBTAINED FROM THIS  PRINT.  NEITHER THIS PRINT NOR ANY PART OF IT NOR ANY INFORMATION CONCERNING IT MAY  BE COPIED,  DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE EXCEPT IN FURTHERANCE OF  YOUR BUSINESS WITH SWAGELOK.  THE PARTS REFERRED TO ON THIS PRINT MAY BE THE  SUBJECT OF PATENTS AND/OR PENDING APPLICATIONS AND MAY NOT BE MANUFACTURED  WITHOUT PERMISSION FROM SWAGELOK COMPANY.

SCALE

NONE

REV.

-

SHEET 

1 of 1

REVISIONS

TOLERANCE ON ENGLISH DIMENSIONS

UNLESS OTHERWISE SPECIFIED

7

6

5

4

3

2

1

D

C

B

A

8

8

7

6

5

4

3

2

1

A

B

C

D

APPROVAL/SCHEDULE DRAWING

               .XX                                    

.031

               .XXX                                  

.015

               ANGLES                

1 DEGREE

DCN

 REV.

Jul-9-12

DATE

DATE

MJR

Jul-9-12

-- DIMENSIONS ARE INCHES NEXT TO [MILLIMETERS].

© Swagelok Company All Rights Reserved

Содержание VCM





















Отзывы:

Нет отзывов