Swagelok VCM Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 20

Swagelok VCM Скачать руководство пользователя страница 17

Valve Control Module

User’s Manual 17

Note: The State Byte will return the value of the sensor if a valve is configured to use a proximity sensor. This

means that the poll response may not be the same value as the command sent.

For example, when valve 1 is connected to a normally closed valve with a BI 1-EG05-AP6X sensor and is
configured to accept sensor input, the response will look like:

Valve

State

Valve

Position

Sensor

State

Valve Indicator

Light

Poll Response

Off

Closed

On

On

1

On

Open

Off

Off

0

Maintenance

There are no field-maintainable parts within the VCM. Contact your authorized Swagelok representative for
assistance.
The following hardware kit is available:

Enclosure Hardware Kit (MS-VCM-KIT1)

This kit contains the components used to attach and seal the interface cover included with the valve control
module, SS-VCM-D-6-2. The contents of this kit are included with that model when shipped from the factory.

■

6 screws

■

6 washers

■

1 interface cover gasket

■

6 acorn nuts

■

6 cable gland O-rings

■

6 cable glands and nuts

Connector Kit (MS-VCM-KIT2)

This kit contains eight #10-32 face seal push-to-connect fittings for use when connecting 1/8 in. plastic tubing
to the valve control module (VCM).

Fig 19 Valve Indicator Light

«
...
15
16
17
18
19
...
»

Содержание VCM





















Отзывы:

Нет отзывов