manualshive.com logo in svg

Swagelok VCM, Руководство пользователя, Страница: 5 / 20

Поделиться
Скачать
Swagelok VCM Скачать руководство пользователя страница 5

Valve Control Module 

User’s Manual     5  

Specifications

Power

Voltage

24 V (dc), nominal

Current 

< 310 mA (dc) at 24 V (dc)

Wattage

< 7.5 W at 24 V (dc)

Temperature

Operating (Ambient)

Minimum

23°F 

(–5°C)

Maximum

122°F

 (50°C)

Media 

Minimum

23°F 

(–5°C)

Maximum

122°F 

(50°C)

Storage

Minimum

–

4°F 

(–20°C)

Maximum

140°F 

(60°C)

Weight

3.5 lb 

(1.6 kg)

Ingress Protection

IP64

Inlet Air

Pressure

40 to 116 psig  

(1.6 to 7.9 bar)

Air Quality

Filtered compressed 

air, lubricated or 

unlubricated, grade of 

filtration 40 μm

Entity Parameters

See control drawing VCM-DN-0011-
SCHEDULE on page 6.

Supported 

Communication 

Baud Rates

Auto-baud function, allowing the device 
to detect the speed of network traffic. It is 
compatible with 125, 250, and 500 kbaud 
rates.

Note:  Before installing the VCM in a hazardous location, review the control drawing on page 6. 

This will help ensure all electrical connections to and from the VCM comply with safety 
requirements. For an electronic copy of this document, see Swagelok.com

Содержание VCM





















Отзывы:

Нет отзывов