Suzuki GSX1300BKA Скачать руководство пользователя страница 22

Страница: 22 / 108

2D-3 Wheels and Tires:

Front Wheel Assembly Removal and Installation
(GSX1300BKAK8)

B823H32406017

Removal

1) Remove the front wheel speed sensor (1).

2) Remove the front wheel assembly (2). Refer to

“Front Wheel Assembly Removal and Installation in
related manual”.

Installation

1) Install the front wheel assembly. Refer to “Front

Wheel Assembly Removal and Installation in related
manual”.

2) Check the clearance between the front wheel speed

sensor and sensor rotor using the thickness gauge.

Special tool

(A): 09900–20803 (Thickness gauge)
(B): 09900–20806 (Thickness gauge)

Wheel speed sensor – Sensor rotor clearance
0.3 – 1.5 mm (0.012 – 0.059 in)

I823H3240001-01

I823H3240002-01

(A),(B)

I823H3240003-01

Содержание GSX1300BKA













































































































Результаты поиска

Содержание GSX1300BKA

Отзывы:

Похожие инструкции для GSX1300BKA

Бренды по названию

Популярные бренды

Suzuki GSX1300BKA, Дополнительное руководство по обслуживанию

Результаты поиска

Содержание GSX1300BKA

Отзывы:

Похожие инструкции для GSX1300BKA

Бренды по названию

Популярные бренды