background image

ABS: 4E-52

DTC “47” (C1647): Supply Voltage (Increased) (GSX1300BKAK8)

B823H34504015

Wiring Diagram

Refer to “ABS Unit Diagram (GSX1300BKAK8) (Page 4E-7)”.

Troubleshooting

NOTE

• After repairing the trouble, clear the DTC using SDS tool. Refer to “DTC (Diagnostic Trouble Code) 

Deleting (GSX1300BKAK8) (Page 4E-25)”.

• When the voltage resumes the normal level, the ABS indicator light will go off.

 

Possible Cause

• Faulty regulator/rectifier.
• Faulty battery.
• Faulty wire harness, etc.

Step

Action

Yes

No

1

1) Turn the ignition switch to OFF.
2) Remove the front seat. Refer to “Exterior Parts Removal 

and Installation in Section 9D in related manual”.

3) Measure the voltage between the (+) and (–) battery 

terminals using the multi-circuit tester.

Special tool

(A):  09900–25008 (Multi-circuit tester set)

Tester knob indication
Voltage (

)

Battery voltage
12.0 V and more

Is the voltage over 12 V?

Go to Step 2.

Charge or replace the 
battery.

2

1) Start the engine at 5 000 r/min with the dimmer switch 

set to HI.

2) Measure the voltage between the (+) and (–) battery 

terminals.

Special tool

:  09900–25008 (Multi-circuit tester set)

Tester knob indication
Voltage (

)

Regulated voltage
14.0 – 15.5 V at 5 000 r/min

Is the voltage 14.0 – 15.5 V?

Go to Step 3.

Inspect the regulator/
rectifier. Refer to 
“Regulator / Rectifier 
Inspection in Section 1J 
in related manual”.

(–)

(

ޓ

)

(A)

I823H3450013-01

Содержание GSX1300BKA













































































































Отзывы: