ABS: 4E-14
7) Loosen the flare nuts (1) and disconnect the brake
pipes.
8) Remove the ABS control unit/HU (2) by removing the
holder nuts (3).
Installation
Installation is in the reverse order of removal. Pay
attention to the following points:
CAUTION
!
• Route the brake hoses and pipes correctly.
Refer to “Front Brake Hose Routing
Diagram (GSX1300BKAK8) in Section 4A
(Page 4A-1)” or “Rear Brake Hose Routing
Diagram (GSX1300BKAK8) in Section 4A
(Page 4A-4)”.
• Make sure to hold the brake pipe when
tightening the flare nut, or it may be
misaligned.
• Temporarily tighten the ABS control unit/HU holder
nuts (1).
• Temporarily tighten the brake pipe flare nuts (2) and
tighten the ABS control unit/HU holder nuts (1).
• Tighten the brake pipe flare nuts (2) to the specified
torque.
Tightening torque
Brake pipe flare nut (a): 16 N·m (1.6 kgf-m, 11.5
lb-ft)
• Bleed air from the brake fluid circuit. Refer to “Air
Bleeding from Brake Fluid Circuit in Section 4A in
related manual”.
Diagnostic Information and Procedures
ABS Troubleshooting (GSX1300BKAK8)
B823H34504001
Many of the ABS malfunction diagnosing operations are
performed by checking the wiring continuity. Quick and
accurate detection of malfunctions within the complex
circuitry assures the proper operation of the ABS. Before
beginning any repairs, thoroughly read and understand
this Supplementary Service Manual.
The ABS is equipped with a self-diagnosis function. The
detected malfunction is stored as a diagnostic trouble
code which causes the ABS indicator light to light up or
flash in set patterns to indicate the malfunction.
Diagnostic trouble codes are stored even when the
ignition switch is turned to OFF and they can only be
erased manually. In order to repair the ABS correctly,
ask the customer for the exact circumstances under
which the malfunction occurred, then check the ABS
indicator light and the output diagnostic trouble codes.
Explain to the customer that depending on how the
motorcycle is operated (e.g., if the front wheel is off the
ground), the ABS indicator light may light up even
though the ABS is operating correctly.
Troubleshooting Procedure
Troubleshooting should be proceed as follows. If the
order is performed incorrectly or any part is omitted, an
error in misdiagnosis may result.
1) Gather information from the customer.
2) Perform the pre-diagnosis inspection. Refer to “Pre-
diagnosis Inspection (GSX1300BKAK8) (Page 4E-
16)”.
3) Inspect the ABS indicator light. Refer to “ABS
Indicator Light Inspection (GSX1300BKAK8)
(Page 4E-19)”.
4) Output the DTCs stored in the ABS control unit.
Refer to “DTC (Diagnostic Trouble Code) Output
(GSX1300BKAK8) (Page 4E-23)”.
1
1
3
2
I823H3450067-02
1
(a)
2
(a)
2
I823H3450069-01
Содержание GSX1300BKA
