manualshive.com logo in svg

Suzuki DF115B, Руководство пользователя

Поделиться
Скачать
Suzuki DF115B Скачать руководство пользователя страница 40

40

NOTE:
A spare plastic lock plate is provided for tempo-
rary use only. Remove it from the cord and
place it in a safe place on board your boat. If
you lose or break the emergency stop switch
cord/lock plate assembly, replace it as soon as
possible so that you can resume normal use of
the emergency stop switch.

STARTING THE ENGINE

NOTE:
If the emergency stop switch lock plate is not in
position, the starter motor cannot operate.

V

 WARNING

Failure to properly attach the emergency stop
switch cord or to take proper precautions to
help ensure that the emergency stop switch
works as intended may result in serious injury
or death to the operator or passengers.

Always take the following precautions:
• Make sure that the emergency stop switch

cord is fastened securely to the operator’s
wrist or to an appropriate clothing area (belt
etc.).

• Ensure that no obstructions impede or

restrict emergency stop switch operation.

• Be careful not to pull the stop switch cord

or knock out the lock plate during normal
operation. The motor will stop abruptly, and
the loss of forward motion may unexpect-
edly throw occupants forward. 

V

 WARNING

Exhaust gas contains carbon monoxide, a
dangerous gas that is difficult to detect
because it is colorless and odorless. Breath-
ing carbon monoxide can cause death or
severe injury.

Never start the engine or let it run indoors or
where there is little or no ventilation. 

If equipped with Keyless Start System:
1. Squeeze the fuel line priming bulb several

times until you feel resistance.

2. Make sure that the warm-up lever is in the

fully closed position.

3. (1) Confirm that the keyless fob is in com-

munication ON mode (Refer to the
“Switching the Communication mode of
the keyless fob” section.)

(2) While the keyless fob is within the com-

munication range of the keyless control
unit, turn the main switch to the “ON &
OFF” position and then release it. The
main switch automatically returns to the
“PUSH START/STOP” position.  
The buzzer sounds twice to notify that
the Keyless Start System has been
turned ON.

NOTE:
If equipped with Dual Engine:
When either one of the engines of Keyless Start
System is turned ON, another engine will auto-
matically be turned ON. 

Содержание DF115B












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды