Suzuki DF115B Скачать руководство пользователя страница 31

Страница: 31 / 75

DIAGNOSTIC SYSTEM

If abnormal conditions exist in any sensor sig-
nal being input to the control unit, the self-diag-
nostic system warns of the abnormal condition.

If this system activates, the red CHECK
ENGINE lamp will flash and a buzzer will
sound.

Also incorporated is a fail-safe provision that
allows the operation at a restricted speed even
under such a failure condition.

The failed system can be identified by the mode
of the lamp flashing and buzzer sounding.

NOTE:
If equipped with Keyless Start System:
This diagnostic code is designed to appear
while the Keyless Start System is in ON state.

If not equipped with Keyless Start System:
This diagnostic code is designed to appear
while the ignition key is turned on.

NOTICE

If the diagnostic system activates while you
are operating your outboard motor, there is an
abnormal condition in one of the sensor sig-
nals of the control system.

Consult your authorized Suzuki marine dealer
for repair of the control system.

NOTE:
If equipped with Keyless Start System:
The buzzer sounds for 60 seconds when the
Diagnostic System is activated, then it stops
automatically.

If not equipped with Keyless Start System:
The buzzer sound with diagnostic system acti-
vating will be canceled by pushing the ignition
key in.

Содержание DF115B












































































Результаты поиска

Содержание DF115B

Отзывы:

Бренды по названию

Популярные бренды

Suzuki DF115B, Руководство пользователя

Результаты поиска

Содержание DF115B

Отзывы:

Бренды по названию

Популярные бренды