manualshive.com logo in svg

Suzuki DF115B, Руководство пользователя

Поделиться
Скачать
Suzuki DF115B Скачать руководство пользователя страница 16

16

Switching the communication mode of 
the keyless fob

Press and hold the lock button 

1

 on the key-

less fob for more than one second to switch
between   ON mode and OFF mode.

ON mode:
The Keyless Start System can be used.

OFF mode:
The Keyless Start System cannot be used.

NOTE:
If the lock button is pressed briefly while in com-
munication ON mode, the LED 

2

 on the key-

less fob briefly flashes once.

KEYLESS FOB BATTERY REPLACEMENT

V

 WARNING

This product contains a coin/button cell bat-
tery. If swallowed, the coin/button cell battery
can cause severe internal burns in just 2
hours and may lead to death.

• THE BATTERY IS A CHEMICAL BURN HAZ-

ARD. DO NOT INGEST THE BATTERY. If you
think batteries might have been swallowed
or placed inside any part of the body, seek
immediate medical attention.

• Keep new and used batteries away from

children. If the battery compartment cannot
be closed securely, stop using this product
and keep it away from children.

If the keyless fob battery runs low, the red
CHECK ENGINE lamp will flash.

V

 CAUTION

There is a danger of explosion if the battery is
replaced with an incorrect type.

Only replace the battery with the same or
equivalent type.

V

 CAUTION

Do not expose Hand Unit to excessive heat
such as from sunlight or fire.

NOTICE

To prevent damage to the keyless fob, be care-
ful when replacing the battery.

• Install the lithium disc-type battery with the

electrodes facing the proper direction.

• Do NOT touch the internal circuit of the key-

less fob when replacing the battery.

Содержание DF115B












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды