manualshive.com logo in svg

Suzuki DF115B, Руководство пользователя

Поделиться
Скачать
Suzuki DF115B Скачать руководство пользователя страница 18

18

SETTING AND/OR CHANGING THE PASS-
CODE

By setting a 4-digit passcode, the engine can
be started by entering the passcode even if the
keyless fob battery has run down or the keyless
fob is lost.
The same method is used to set and change
the passcode.

NOTE:
Carry the passcode with the emergency key in
case the keyless fob battery runs down or the
keyless fob is lost. 

NOTE:
When the passcode has been updated or
changed, the previous passcode is deleted and
updated to the new passcode.

Use the following procedure to set or change
the passcode: 
1. Confirm the engine is stopped. 
2. Make sure the emergency switch lock plate

is in place.

3. Confirm the keyless fob is within the commu-

nication range of the Keyless Start System. 

4. Confirm that the keyless fob is in communi-

cation ON mode. (Refer to “Switching the
communication mode of the keyless fob”
section.)

5. Turn the main switch to the “ON & OFF”

position and then release it. The main switch
automatically returns to the “PUSH START/
STOP” position. 
The buzzer on the engine control side emits
one (1) long sound while the buzzer on the
keyless control unit side emits two (2) short
sounds simultaneously. 

ON & OFF

ON & OFF

PUSH
START

STOP

PUSH
START

STOP

6. Pull out the emergency stop switch lock

plate.

7. Within eight (8) seconds after performing

Step 5, start the following operation. 

(1) Turn the main switch to the “ON & OFF”

position and hold it for about five (5) seconds
then release it to the “PUSH START/STOP”
position. 
Repeat this operation for two more times.
The buzzer sounds once and the system
enters stand-by mode for passcode input.

NOTE:
The buzzer will not sound if the operation in
Step (1) is not performed within eight (8) sec-
onds or the operation fails. 

(2) Within 60 seconds after performing Step (1),

turn the main switch to the “ON & OFF” posi-
tion and then release it. The main switch
automatically returns to the “PUSH START/
STOP” position.
The buzzer starts emitting short sounds.
Briefly turn the switch after the number of
sounds that is the same as the first pass-
code digit. For example, if the first passcode
digit is seven, turn the switch after the sev-
enth sound.
To set or select zero (0), turn the switch after
the 10th sound.

ON & OFF

ON & OFF

ON & OFF

PUSH
START

STOP

PUSH
START

STOP

Hold it for five (5) seconds. 

Содержание DF115B












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды