manualshive.com logo in svg

Suzuki DF115B, Руководство пользователя

Поделиться
Скачать
Suzuki DF115B Скачать руководство пользователя страница 35

35

TILT LOCK LEVER

The Tilt Lock Lever is provided so you can sup-
port the motor in a tilted position for non-moving
engine support.

To set the Tilt Lock Lever:
1. Tilt the motor all the way up by pressing the

Power Trim and Tilt “UP” switch.

2. Pull down the Tilt Lock Lever Lever as

shown in the illustration.

3. Lower the motor by pressing the Power Trim

and Tilt “DOWN” switch, until the motor is
supported by the Tilt Lock Lever.

4. For DF140B:

Continue to operate the Power Trim and Tilt
“DOWN” switch until the trim rods are com-
pletely retracted. 

To release the Tilt Lock Lever, tilt the motor all
the way up using the Power Trim and Tilt “UP”
switch, and pull up the Tilt Lock Lever.

NOTICE

If you do not retract the trim rams completely
when mooring, they may become deteriorated
or corroded.

Be sure to retract the trim rams completely
when mooring.

If equipped with Keyless Start System:

If not equipped with Keyless Start System:

V

 CAUTION

The remote Power Trim and Tilt switch will
work when the Keyless start system is off. If
someone activates the switch while you are
moving the tilt lock lever, your hand could be
injured.

Keep all persons away from the remote Power
Trim and Tilt switch while you are moving the
tilt lock lever.

NOTICE

Damage can occur if you use the tilt lock lever
other than when the boat is moored or is oth-
erwise stationary.

The tilt lock lever relieves pressure from the
power trim and tilt and should only be used
when the boat is stationary. Do not use the tilt
lock lever when trailering your boat and
motor. Refer to the TRAILERING section of
this manual.

V

 CAUTION

The remote Power Trim and Tilt switch will
work when the ignition switch is off. If some-
one activates the switch while you are moving
the tilt lock lever, your hand could be injured.

Keep all persons away from the remote Power
Trim and Tilt switch while you are moving the
tilt lock lever.

NOTICE

Damage can occur if you use the tilt lock lever
other than when the boat is moored or is oth-
erwise stationary.

The tilt lock lever relieves pressure from the
power trim and tilt and should only be used
when the boat is stationary. Do not use the tilt
lock lever when trailering your boat and
motor. Refer to the TRAILERING section of
this manual.

Содержание DF115B












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды