Supero X9DBL-3, Руководство пользователя

Страница: 57 / 113

Chapter 2: Installation
2-33
JD1
JPW1
JIPMB1
LED3
T-SGPIO1 T-SGPIO2
JSTBY1
J9
JBT1
JPI2C1
JF1(FP Control)
TPM/Port80
JL1
JI2C1
JI2C2
JOH1
LED1
JWP1
JBR1
JPME1
JVRM_I2C1
JVRM_I2C2
JPG1
JPB1
JPL1
JPL2
JCPUVRD_SMB
I-SATA1
I-SATA0
S-SATA/
SAS0
1 7
I-SATA2
I-SATA3
I-SATA4
I-SATA5
BT1
SP1
FAN4
FAN1
FAN2
FAN5
FANA
FAN3
JPW2
JPW3
SCU- SGPIO1
USB2/3
USB4/5
KB/MOUSE
CPU1 SLOT2 PCI-E 3.0 X4(IN X8)
CPU1
P2-DIMM1F P2-DIMM1E P2-DIMM1D
P1-DIMM1B P1-DIMM1A
P1-DIMM1C
LAN2
CPU2 SLOT3 PCI-E 3.0 X8
CPU2 SLOT5 PCI-E 3.0 X8
CPU2 SLOT4 PCI-E 3.0 X8
CPU1 SLOT6 PCI-E 3.0 X16
SLOT1 PCI 33MHZ
USB6
IPMI_LAN
VGA COM1
USB0/1
LAN1
COM2
CPU2
JWD1
BIOS
Battery
LAN CTRL
LAN CTRL
BMC CTRL
CPLD
Intel PCH
X9DBL-i/3 (F)
Rev. 1.01
LED2
JUIDB1
SCU- SGPIO2
S-SATA/
SAS1
S-SATA/
SAS2
S-SATA/
SAS3
S-SATA/
SAS4
S-SATA/
SAS5
S-SATA/SAS6
S-SATA/
SAS7
CMOS Clear
JBT1 is used to clear CMOS. Instead of pins, this "jumper" consists of contact pads
to prevent accidental clearing of CMOS. To clear CMOS, use a metal object such
as a small screwdriver to touch both pads at the same time to short the connection.
Always remove the AC power cord from the system before clearing CMOS.
Note 1.
For an ATX power supply, you must completely shut down the sys-
tem, remove the AC power cord, and then short JBT1 to clear CMOS.
Note 2. Be sure to remove the onboard CMOS Battery before you short
JBT1 to clear CMOS.
Note 3. Clearing CMOS will also clear all passwords.
A. Clear CMOS
B. Watch Dog Enable
Watch Dog Enable/Disable
Watch Dog (JWD1) is a system monitor that
can reboot the system when a software appli-
cation hangs. Close Pins 1-2 to reset the sys-
tem if an application hangs. Close Pins 2-3 to
generate a non-maskable interrupt signal for
the application that hangs. See the table on
the right for jumper settings. Watch Dog must
also be enabled in the BIOS.
Watch Dog
Jumper Settings
Jumper Setting Definition
Pins 1-2 Reset (default)
Pins 2-3 NMI
Open Disabled
A
B