Supero SUPER P4DME-M Скачать руководство пользователя страница 62

Страница: 62 / 86

UPER P4DMS-6GM/P4DME-M User's Manual

4-12

Advanced Chipset Control

Access the submenu to make changes to the following settings.

Enable Memory Gap

This setting allows you to turn off system RAM to free up address space.

The options for this setting are Disabled and Extended.

ECC Configuration

This setting lets you enable or disable ECC (Error Correction and

Checking). The options are ECC and Disabled.

ECC Error Type

This setting lets you select which type of interrupt will be activated as a

result of an ECC error. The options are None, NMI (Non-Maskable

Interrupt), SMI (System Management Interrupt) and SCI (System Control

Interrupt.

SERR Signal Condition

This setting specifies the conditions required to qualify as an ECC error.

Options are None, Single Bit, Multiple Bit and Both.

Advanced Processor Options

Access the submenu to make changes to the following settings.

CPU Speed

This is a display that indicates the speed of the installed processor.

Frequency Ratio

This setting allows you to specify the value of tthe internal frequency

multiplier of the processor, which is used to determine the processor

speed. Options are x8, x16, x17, x18, x19 and x20.

Содержание SUPER P4DME-M























































































Результаты поиска

Содержание SUPER P4DME-M

Отзывы:

Похожие инструкции для SUPER P4DME-M

Бренды по названию

Популярные бренды

Supero SUPER P4DME-M, Руководство пользователя

Результаты поиска

Содержание SUPER P4DME-M

Отзывы:

Похожие инструкции для SUPER P4DME-M

Бренды по названию

Популярные бренды