Supero SUPER P4DME-M Скачать руководство пользователя страница 21

Страница: 21 / 86

Chapter 1: Introduction

1-15

Introduction

CPU Fan Auto-Off in Sleep Mode

The CPU fan activates when the power is turned on. It continues to operate

when the system enters Standby mode. When in sleep mode, the CPU will

not run at full power, thereby generating less heat.

CPU Overheat LED

JOH1 is a header used to connect to a CPU overheat LED. When the CPU

temperature becomes too high, both the overheat fan and the warning LED

are activated.

System Resource Alert

This feature is available when used with Intel's LANDesk Client Manager

(optional). LDCM is used to notify the user of certain system events. For

example, if the system is running low on virtual memory and there is insuf-

ficient hard drive space for saving the data, you can be alerted of the

potential problem.

Auto-Switching Voltage Regulator for the CPU Core

The auto-switching voltage regulator for the CPU core can support up to

20A current and auto-sense voltage IDs ranging from 1.4V to 3.5V. This

will allow the regulator to run cooler and thus make the system more stable.

1-5

ACPI Features

ACPI stands for Advanced Configuration and Power Interface. The ACPI

specification defines a flexible and abstract hardware interface that pro-

vides a standard way to integrate power management features throughout

a PC system, including its hardware, operating system and application soft-

ware. This enables the system to automatically turn on and off peripherals

such as CD-ROMs, network cards, hard disk drives and printers. This also

includes consumer devices connected to the PC such as VCRs, TVs, tele-

phones and stereos.

Содержание SUPER P4DME-M























































































Результаты поиска

Содержание SUPER P4DME-M

Отзывы:

Похожие инструкции для SUPER P4DME-M

Бренды по названию

Популярные бренды

Supero SUPER P4DME-M, Руководство пользователя

Результаты поиска

Содержание SUPER P4DME-M

Отзывы:

Похожие инструкции для SUPER P4DME-M

Бренды по названию

Популярные бренды