Supero SUPER P4DME-M Скачать руководство пользователя страница 79

Страница: 79 / 86

A-5

Appendix A: PhoenixBIOS POST Messages

Parity Check 2 nnnn

Parity error found in the I/O bus. BIOS attempts to locate the address and display

it on the screen. If it cannot locate the address, it displays ????.

Press <F1> to resume, <F2> to Setup, <F3> for previous

Displayed after any recoverable error message. Press <F1> to start the boot

process or <F2> to enter Setup and change the settings. Press <F3> to display

the previous screen (usually an initialization error of an Option ROM, i.e., an

add-on card). Write down and follow the information shown on the screen.

Press <F2> to enter Setup

Optional message displayed during POST. Can be turned off in Setup.

PS/2 Mouse:

PS/2 mouse identified.

Run the I2O Configuration Utility

One or more unclaimed block storage devices have the Configuration Request bit

set in the LCT. Run an I2O Configuration Utility (e.g. the SAC utility).

System BIOS shadowed

System BIOS copied to shadow RAM.

UMB upper limit segment address:

nnnn

Displays the address

nnnn

of the upper limit of Upper Memory Blocks,

indicating released segments of the BIOS which can be reclaimed by a virtual

memory manager.

Video BIOS shadowed

Video BIOS successfully copied to shadow RAM.

Содержание SUPER P4DME-M























































































Результаты поиска

Содержание SUPER P4DME-M

Отзывы:

Похожие инструкции для SUPER P4DME-M

Бренды по названию

Популярные бренды

Supero SUPER P4DME-M, Руководство пользователя

Результаты поиска

Содержание SUPER P4DME-M

Отзывы:

Похожие инструкции для SUPER P4DME-M

Бренды по названию

Популярные бренды