Supero SUPER P4DME-M Скачать руководство пользователя страница 78

Страница: 78 / 86

UPER P4DMS-6GM/P4DME-M

User’s Manual

A-4

Fixed Disk n

Fixed disk n (0-3) identified.

Invalid System Configuration Data

Problem with NVRAM (CMOS) data.

I/O device IRQ conflict

I/O device IRQ conflict error.

PS/2 Mouse Boot Summary Screen:

PS/2 Mouse installed.

nnnn kB Extended RAM Passed

Where nnnn is the amount of RAM in kilobytes successfully tested.

nnnn Cache SRAM Passed

Where nnnn is the amount of system cache in kilobytes successfully tested.

nnnn kB Shadow RAM Passed

Where nnnn is the amount of shadow RAM in kilobytes successfully

tested.

nnnn kB System RAM Passed

Where nnnn is the amount of system RAM in kilobytes successfully tested.

One or more I2O Block Storage Devices were excluded from the Setup

Boot Menu

There was not enough room in the IPL table to display all installed I2O block-

storage devices.

Operating system not found

Operating system cannot be located on either drive A: or drive C:. Enter Setup

and see if fixed disk and drive A: are properly identified.

Parity Check 1 nnnn

Parity error found in the system bus. BIOS attempts to locate the address and

display it on the screen. If it cannot locate the address, it displays ????. Parity is

a method for checking errors in binary data. A parity error indicates that some

data has been corrupted.

Содержание SUPER P4DME-M























































































Результаты поиска

Содержание SUPER P4DME-M

Отзывы:

Похожие инструкции для SUPER P4DME-M

Бренды по названию

Популярные бренды

Supero SUPER P4DME-M, Руководство пользователя

Результаты поиска

Содержание SUPER P4DME-M

Отзывы:

Похожие инструкции для SUPER P4DME-M

Бренды по названию

Популярные бренды