Supermicro SUPERSERVER 6014V-T2 Скачать руководство пользователя страница 81

Страница: 81 / 120

Chapter 7: BIOS

7-15

Remote Access Conﬁ guration

You can use this screen to select options for the Remote Access Conﬁ guration. Use

the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus>

keys to change the value of the selected option.

Remote Access

This feature allows the user to disable Remote Access function. If Disabled is not

selected, then you can select a Remote Access type. The options are Enabled

and

Disabled

USB Conﬁ guration

USB Function

This setting allows you to

Enable

or Disable the USB.

Legacy USB Support

Select Enabled to support USB Legacy. Disable Legacy support if there are no USB

devices installed in the system. The options are Disabled,

Enabled

and Auto.

USB 2.0 Controller

This setting allows you to

Enable

or Disable the USB 2.0 Controller.

USB 2.0 Controller Mode

This setting allows you to conﬁ gure USB 2.0 Controller Mode. The options are

Hi-Speed (480 Mbps)

and Full Speed-12Mbps.

USB Mass Storage Device Conﬁ gura tions

USB Mass Storage Reset Delay

This setting allows you to decide how long the system shall wait in an attempt

to detect the presence of a USB Mass Storage Device before it issues a start

command to proceed with the next operation during POST. The options are

10 Seconds,

20 Seconds

, 30 Seconds and 40 Seconds.

Emulation Type

If set to Auto, USB devices that are smaller than 530MB will be emulated as

ﬂ oppy, while remaining as a HDD. Forced FDD option will allow you to conﬁ gure

a HDD formatted drive to boot as a FDD (Eg. Zip Drive). The options are:

Auto

Floppy, Forced FDD, Hard Disk and CD ROM.

Содержание SUPERSERVER 6014V-T2

























































































































Результаты поиска

Содержание SUPERSERVER 6014V-T2

Отзывы:

Supermicro SUPERSERVER 6014V-T2, Руководство пользователя, Страница: 81 / 120

Результаты поиска

Содержание SUPERSERVER 6014V-T2

Отзывы: