manualshive.com logo in svg

Supermicro SUPERSERVER 6014V-T2, Руководство пользователя, Страница: 51 / 120

Поделиться
Скачать
Supermicro SUPERSERVER 6014V-T2 Скачать руководство пользователя страница 51

Chapter 5: Advanced Serverboard Setup

5-15

Wake-On-LAN

The Wake-On-LAN header is desig-

nated WOL.  See the table on the right 

for pin defi nitions.  You must enable 

the LAN Wake-Up setting in BIOS to 

use this feature.  You must also have 

a LAN card with a Wake-on-LAN con-

nector and cable.

Wake-On-Ring

The Wake-On-Ring header is desig-

nated JWOR.  This function allows 

your computer to receive and "wake-

up" by an incoming call to the modem 

when in suspend state.  See the table 

on the right for pin defi nitions.  You 

must have a WOR card and cable to 

use this feature. 

Wake-On-Ring

Pin Defi nitions 

(JWOR)

Pin#     Defi nition     

1

Ground (Black)

2

Wake-up

Wake-On-LAN

Pin Defi nitions (WOL)

Pin#     Defi nition     

1

+5V Standby

2

Ground

3

Wake-up

SMB Power (I

2

C)

The header at PW3 is for I

2

C, which 

may be used to monitor the status of 

the power supply, fan and system tem-

perature.  See the table on the right for 

pin defi nitions.

SMB Power (I

2

C)  

Pin Defi nitions (PW3)

Pin#     Defi nition     

1

Clock

2

SMB Data

3

N/A

4

N/A

5

N/A

Содержание SUPERSERVER 6014V-T2

























































































































Отзывы:

Нет отзывов