Supermicro SUPERSERVER 6014V-T2 Скачать руководство пользователя страница 78

Страница: 78 / 120

7-12

UPER

ERVER 6014V-T2 User's Manual

SouthBridge Conﬁ guration

This feature allows the user to conﬁ gure the settings for the Intel ICH SouthBridge

chipset.

CPU B.I.S.T. Enable

Select Enabled to enable the function of CPU Built In Self Test. The options are

Enabled and

Disabled

ICH Delayed Transaction

Select Enabled to enable the function of ICH Delayed Transaction to provide back-

compatibility for slower components. The options are

Enabled

and Disabled.

ICH DCB Enable

Select Enabled to enable ICH DMA Collection Buffer. The options are

Enabled

and Disabled.

ACPI Conﬁ guration

Advanced ACPI Conﬁ guration

ACPI 2.0 Features

Select Yes to allow RSDP pointers to point to the 64-bit Fixed System Description

Tables. Select No to deactivate this function. The options are Yes and

ACPI APIC Support

Select Enabled to allow the ACPI APIC Table Pointer to be included in the RSDP

pointer list. The options are

Enable

and Disabled.

AMI OEMB Table

Select Enabled to allow the OEMB Table Pointer to be included in the R(x)SDT

pointer lists. The options are

Enable

and Disabled.

Headless Mode

Select Enabled to activate the Headless Operation Mode through ACPI, which

will allow the system to boot up and function properly without keyboard and

monitor display. The options are Enabled and

Disabled

Содержание SUPERSERVER 6014V-T2

























































































































Результаты поиска

Содержание SUPERSERVER 6014V-T2

Отзывы:

Supermicro SUPERSERVER 6014V-T2, Руководство пользователя, Страница: 78 / 120

Результаты поиска

Содержание SUPERSERVER 6014V-T2

Отзывы: