Supermicro SUPERSERVER 6014V-T2 Скачать руководство пользователя страница 106

Страница: 106 / 120

C-8

UPER

ERVER 6014V-T2 User's Manual

5. When ﬁ nished, press

Done

(as shown on the following screen).

Note:

If you select Migrate for RAID 0, or Build for RAID 1, you will be asked to

select the source drive. The contents of the source drive will be preserved. However,

the data on the new drive will be lost.

Raid Level

Create Via

When Appropriate

RAID 0

No Init

Creating a RAID 0 on new drives

RAID 0

Migrate
(*Note)

Creating a RAID 0 from one new drive and
one drive with data you wish to preserve

RAID 1

Build1

Any time you wish to create a RAID 1, but especially if
you have data on one drive that you wish to preserve

RAID 1

Clear

Creating a RAID 1 on new drives, or when you want to
ensure that the array contains no data after creation.

RAID 1

Quick

RAID 1

Init

Fastest way to create a RAID 1.
Appropriate when using new drives

4. The item

"Create RAID via"

allows you to select between the different meth-

ods of creating RAID 0 and RAID 1.

The following table gives examples of when each is appropriate.

Содержание SUPERSERVER 6014V-T2

























































































































Результаты поиска

Содержание SUPERSERVER 6014V-T2

Отзывы:

Supermicro SUPERSERVER 6014V-T2, Руководство пользователя, Страница: 106 / 120

Результаты поиска

Содержание SUPERSERVER 6014V-T2

Отзывы: