Supermicro SUPERSERVER 6014V-T2 Скачать руководство пользователя страница 41

Страница: 41 / 120

Chapter 5: Advanced Serverboard Setup

5-5

Figure 5-3. Front Control Panel Header Pins (JF1)

Connecting the Control Panel

JF1 contains header pins for various front control panel connectors. See Figure

5-3 for the pin locations of the various front control panel buttons and LED indi-

cators. Please note that even and odd numbered pins are on opposite sides of

each header.

All JF1 wires have been bundled into single keyed ribbon cable to simplify their

connection. The red wire in the ribbon cable plugs into pin 1 of JF1. Connect

the other end of the cable to the Control Panel printed circuit board, located just

behind the system status LEDs in the chassis.

See the Connector Deﬁ nitions section in this chapter for details and pin descrip-

tions of JF1.

NMI

x (key)

Vcc

Reset Button

Power Button

Ground

x (key)

Power LED

HDD LED

NIC1

NIC2

OH/Fan Fail LED

Power Fail LED

Ground

2 1

20 19

Содержание SUPERSERVER 6014V-T2

























































































































Результаты поиска

Содержание SUPERSERVER 6014V-T2

Отзывы:

Supermicro SUPERSERVER 6014V-T2, Руководство пользователя, Страница: 41 / 120

Результаты поиска

Содержание SUPERSERVER 6014V-T2

Отзывы: