Supermicro SUPERSERVER 1018R-WC0R Скачать руководство пользователя страница 6

Страница: 6 / 76

Chapter 1

Introduction

1-1 Overview

The SuperServer 1018R-WC0R is comprised of two main subsystems: the
SC116AC-R706WB 1U chassis and the X10SRW-F motherboard. Please refer to

our web site for information on operating systems that have been certified for use

with the system (www.supermicro.com).
In addition to the motherboard and chassis, various hardware components have
been included with the 1018R-WC0R, as listed below:

•

One passive CPU heatsink (SNK-P0047PS)

•

Six 4-cm PWM fans (FAN-0101L4)

•

One air shroud (MCP-310-19002-0N)

•

SATA

Accessories

One SAS/SATA backplane (BPN-SAS3-116A)

Ten drive carriers (MCP-220-00047-0B)

•

Two riser cards (RSC-R1UW-2E16-O-P, RSC-R1UW-E8R-O-P)

Note:

For your system to work properly, please follow the links below to download

all necessary drivers/utilities and the user’s manual for your server.

•

Supermicro product manuals:

http://www.supermicro.com/support/manuals/

•

Product drivers and utilities:

ftp://ftp.supermicro.com

•

Product safety info:

http://www.supermicro.com/about/policies/safety_informa-

tion.cfm

•

If you have any questions, please contact our support team at:

[email protected]

Chapter 1: Introduction

1-1

Содержание SUPERSERVER 1018R-WC0R













































































Результаты поиска

Содержание SUPERSERVER 1018R-WC0R

Отзывы:

Похожие инструкции для SUPERSERVER 1018R-WC0R

Бренды по названию

Популярные бренды

Supermicro SUPERSERVER 1018R-WC0R, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 1018R-WC0R

Отзывы:

Похожие инструкции для SUPERSERVER 1018R-WC0R

Бренды по названию

Популярные бренды