Supermicro SUPERSERVER 1018R-WC0R Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 76

background image

Chapter 6: Advanced Chassis Setup

6-5

6-4

S

UPER

S

ERVER 1018R-WC0R User's Manual

Figure 6-3. Replacing a System Fan

Checking the Airflow

Check the Airflow

1.

Make sure there are no objects obstructing the airflow in and out of the
server. In addition, if you are using a front bezel, make sure the bezel's filter

is replaced periodically.

2. Do not operate the server without hard drives or drive carriers in the drive

bays. Use only recommended server parts.

3.

Make sure no wires or foreign objects obstruct airflow through the chassis.
Pull all excess cabling out of the airflow path or use shorter cables.

4. The control panel LEDs inform you of system status. See Chapter 3 System

Interface for details on the LEDs and the control panel buttons.

6-5 Drive Bay Installation/Removal

Accessing the Drive Bays

Hard Drives: Because of their hotswap capability, you do not need to access the
inside of the chassis or power down the system to install or replace hard drives.

Refer to the figure below for the drive bay configuration on the 1018R-WC0R.

Replacing a System Fan

1. Open the chassis while the system is running to determine which fan has

failed. Never run the server for an extended period of time with the chassis
open.

2. Turn off the power to the system and unplug the power cord from the power

supply.

3. Remove the failed fan's wiring from the fan header on the motherboard.

4. Lift the failed fan from the chassis and pull it completely out.

5. Place the new fan into the vacant space in the housing while making sure the

arrows on the top of the fan (indicating air direction) point in the same direc-
tion as the arrows on the other fans.

6. Reconnect the fan wires to the same chassis fan header as the previous fan.

7. Power up the system and check that the fan is working properly before re-

placing the chassis cover.

Figure 6-4. Logical Hard Drives

HDD0

SAS3

HDD2

SAS3

HDD4

SAS3

HDD6

SAS3

HDD1

SAS3

HDD3

SAS3

HDD5

SAS3

HDD7

SAS3

HDD9

SATA3

HDD8

SATA3

«
...
45
46
47
48
49
...
»

Содержание SUPERSERVER 1018R-WC0R













































































Отзывы:

Нет отзывов

Похожие инструкции для SUPERSERVER 1018R-WC0R

ShareCenter Pro DNS-1200-05

Бренд: D-Link Страницы: 68

NEAX2000 IVS Series

Бренд: NEC Страницы: 160

Бренд: Sun Fire Страницы: 66

Бренд: Synology Страницы: 15

Бренд: AIC Страницы: 112

Бренд: B&B Страницы: 70

Бренд: Conceptronic Страницы: 127

Бренд: HIKVISION Страницы: 13

Бренд: EMC Страницы: 34

SuperServer 6019P-WT

Бренд: Supermicro Страницы: 133

Бренд: Hamlet Страницы: 76

SUPERSERVER 6015C-NT

Бренд: Supermicro Страницы: 110

Бренд: D-Link Страницы: 40

Бренд: Advantech Страницы: 3

Бренд: Blonder tongue Страницы: 20

Бренд: Meinberg Страницы: 34

AS1021M-UR Plus

Бренд: Supero Страницы: 104

Бренд: Supero Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды