Supermicro SUPERO SUPERSERVER 1028R-WTR Series Скачать руководство пользователя страница 14

Страница: 14 / 126

1-4

SUPERSERVER

1028R-WTR(T) USER'S MANUAL

Cooling System

The SC116 chassis has an innovative cooling design that features up to six sets

of 4-cm counter-rotating fans located in the middle section of the chassis. These

fans are 1U high and are powered by 4-pin connectors, with chassis fan speed

controlled by IPMI software. The power supply module also includes a cooling fan.

Note:

The fans in this system are NOT redundant, hot-plug.

1-6 Advanced Power Management

Intel® Intelligent Power Node Manager (IPNM)

The Intel

Intelligent Power Node Manager (IPNM) provides your system with

real-time thermal control and power management for maximum energy effi ciency.

Although IPNM Specifi cation Version 2.0 is supported by the BMC (Baseboard

Management Controller), your system must also have IPNM-compatible

Manageability Engine (ME) 2.0 fi rmware installed to use this feature.

Manageability Engine (ME)

The Manageability Engine, which is an ARC controller embedded in the IOH (I/O

Hub), provides Server Platform Services (SPS) to your system. The services

provided by SPS are different from those proveded by the ME on client platforms.

Содержание SUPERO SUPERSERVER 1028R-WTR Series































































































































Результаты поиска

Содержание SUPERO SUPERSERVER 1028R-WTR Series

Отзывы:

Похожие инструкции для SUPERO SUPERSERVER 1028R-WTR Series

Бренды по названию

Популярные бренды

Supermicro SUPERO SUPERSERVER 1028R-WTR Series, Руководство пользователя

Результаты поиска

Содержание SUPERO SUPERSERVER 1028R-WTR Series

Отзывы:

Похожие инструкции для SUPERO SUPERSERVER 1028R-WTR Series

Бренды по названию

Популярные бренды