Supermicro SUPERO SUPERSERVER 1028R-WTR Series Скачать руководство пользователя страница 27

Страница: 27 / 126

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel and on the drive carriers that provide

system and component status for the 1028R-WTR(T) server. This chapter explains

the meanings of all LED indicators and the appropriate responses that need to be

taken.

3-2 Control Panel Buttons

There are two buttons located on the front of the chassis: a power on/off button

and a UID button.

Figure 3-1. Control Panel Buttons and LEDs

Power

The main power switch is used to apply or remove power from the power supply

to the server system. Turning off system power with this button removes the main

power but keeps standby power supplied to the system. Therefore, you must unplug

system before servicing.

Содержание SUPERO SUPERSERVER 1028R-WTR Series































































































































Результаты поиска

Содержание SUPERO SUPERSERVER 1028R-WTR Series

Отзывы:

Похожие инструкции для SUPERO SUPERSERVER 1028R-WTR Series

Бренды по названию

Популярные бренды

Supermicro SUPERO SUPERSERVER 1028R-WTR Series, Руководство пользователя

Результаты поиска

Содержание SUPERO SUPERSERVER 1028R-WTR Series

Отзывы:

Похожие инструкции для SUPERO SUPERSERVER 1028R-WTR Series

Бренды по названию

Популярные бренды