Supermicro A+ SERVER 1012C-MRF Скачать руководство пользователя страница 97

Страница: 97 / 116

Chapter 7: BIOS

7-5



Advanced Chipset Control



NorthBridge Configuration



Memory Configuration

Bank Interleaving

Select Auto to automatically enable a bank-interleaving memory scheme
when this function is supported by the processor. The options are

Auto

and Disabled.

Node Interleaving

This option enables node memory interleaving. Options include Auto or

Disabled

Channel Interleaving

This option enables channel memory interleaving. Options include

Auto

or Disabled.

CS Sparing

This setting will reserve a spare memory rank in each node when enabled.
Options are Enabled and

Disabled

Bank Swizzle Mode

This setting

Enables

or Disables the bank swizzle mode.



ECC Configuration

ECC Mode

This submenu affects the DRAM scrub rate based on its setting. Options
include Disabled,

Basic

, Good, Super, Max and User. Selecting User

activates the other options for user setting.

DRAM ECC Enable

This setting allows hardware to report and correct memory errors
automatically, maintaining system integrity. Options are

Enabled

Disabled. This is option is only active if ECC Mode above is set to

User

Содержание A+ SERVER 1012C-MRF





















































































































Результаты поиска

Содержание A+ SERVER 1012C-MRF

Отзывы:

Похожие инструкции для A+ SERVER 1012C-MRF

Бренды по названию

Популярные бренды

Supermicro A+ SERVER 1012C-MRF, Руководство пользователя

Результаты поиска

Содержание A+ SERVER 1012C-MRF

Отзывы:

Похожие инструкции для A+ SERVER 1012C-MRF

Бренды по названию

Популярные бренды